Kan ik de Powerline Adapter Ontvanger SCS-P1200P1 los gebruiken zonder zender?

Nee, de ontvanger kan niet zelfstandig functioneren. De SCS-P1200P1 heeft altijd een gekoppelde Powerline zender nodig, zoals de SCS-P1200P2 of een zender uit een complete Powerline set. Zonder zender is er geen dataoverdracht via het stroomnet en zal de ontvanger geen netwerkverbinding tot stand brengen.

Waar plaats ik de ontvanger in mijn installatie?

U plaatst de ontvanger bij voorkeur in een stopcontact in de buurt van uw router, netwerk-switch of NVR en verbindt deze met een UTP-kabel. Zo komt al het verkeer van de Powerline zenders via het stroomnet samen bij dit centrale punt in uw netwerk.

Werkt deze ontvanger alleen met de SCS-P1200P2 zender?

De SCS-P1200P1 is ontworpen om samen te werken met de SCS-P1200P2 Powerline zender en bijbehorende sets op basis van HomePlug AV2. Voor een betrouwbare werking adviseren wij de ontvanger te combineren met de bijbehorende zender en niet te mengen met willekeurige andere Powerline-systemen.

Is de snelheid van 1200 Mbps altijd haalbaar?

De 1200 Mbps is een theoretische maximale snelheid. In de praktijk hangt de werkelijke snelheid af van de kwaliteit van de elektrische installatie, de lengte van de kabels, het aantal groepen en eventuele storingsbronnen. Voor de meeste IP-camera en netwerktoepassingen is de praktische snelheid echter ruim voldoende.

Kan ik andere apparaten dan IP-camera’s aansluiten op de ontvanger?

Ja, u kunt elk apparaat met een bekabelde Ethernet-aansluiting op de ontvanger aansluiten, zoals een NVR, computer, switch of ander netwerkapparaat. Het werkt in de praktijk hetzelfde als een gewone netwerkkabel, zolang het totale dataverkeer binnen redelijke grenzen blijft.

Heeft de Powerline Adapter Ontvanger invloed op het stroomnet of andere apparaten?

De Powerline Adapter Ontvanger gebruikt het stroomnet als transportmedium voor datasignalen, maar heeft geen merkbare invloed op uw normale stroomverbruik. Andere apparaten op dezelfde groep blijven gewoon functioneren. In sommige gevallen kunnen zware of storende apparaten de datasnelheid beïnvloeden, maar dit heeft geen negatieve impact op de veiligheid of werking van de stroomvoorziening.

Powerline Adapter Receiver | Easy Network Expansion via Powerline

SKU	8147

The SCS-P1200P1 Powerline Adapter Receiver forms the receiving part of a Powerline network and is installed near your router, modem, or NVR. The receiver receives the network signal from a connected Powerline transmitter via the existing electrical wiring and converts it to a standard UTP network connection. This allows you to easily connect IP cameras and other network devices via the mains without having to run new network cables throughout the building.

It's important to know that this receiver cannot function independently. The Powerline Adapter Receiver SCS-P1200P1 always requires a Powerline transmitter, such as the SCS-P1200P2 or a complete Powerline set. Without a transmitter, no network connection will be established, and the connected recorder or router will not receive data.

Application: central receiving point in the Powerline network

The SCS-P1200P1 Powerline Adapter Receiver serves as a central receiving point in the Powerline network. You place the receiver near your router, switch, or NVR, so that all data from one or more Powerline transmitters is collected there via the electrical wiring. This is ideal for camera systems and other fixed network solutions in homes, businesses, warehouses, and outbuildings.

– Receiving point for data from Powerline transmitters in the power grid
– Central connection between IP cameras and NVR or router
– Suitable for fixed network equipment without WiFi
– Suitable for homes, shops, offices and commercial spaces

Operation in combination with a Powerline transmitter

In a typical setup, the Powerline transmitter is placed near the IP camera and connected with a UTP cable. The transmitter then sends the data via the electrical wiring to the SCS-P1200P1 Powerline Adapter Receiver. This receiver is placed near the router or NVR and creates a regular network connection point there. To the recorder or router, the connection behaves like a regular network cable, while the signal actually travels via the electrical wiring.

– Transmitter at the IP camera in a socket with UTP connection
– Receiver at the router or NVR in a socket with UTP connection
– Data exchange via the existing power network
– No additional network cables required through walls or ceilings

Key Features of the Powerline Adapter Receiver

The SCS-P1200P1 Powerline Adapter Receiver supports speeds up to 1200 Mbps and uses HomePlug AV2 technology. This ensures a stable and smooth connection, suitable for forwarding camera images and other network data. The receiver works seamlessly within your network, without complicated configuration or software installation.

– Maximum throughput speed up to 1200 Mbps
– HomePlug AV2 for stable Powerline communication
– Support for IEEE 802.3 and 802.3u (10/100 Ethernet)
– Transparent operation within the network, no complex installation
– Compact design, easy to place near router or recorder

Installation: plug & play with router or NVR

Installing the SCS-P1200P1 Powerline Adapter Receiver is easy and requires no in-depth networking knowledge. Once the corresponding transmitter is correctly paired, the receiver automatically recognizes the Powerline connection, and the network access point is ready for use.

1. Plug the receiver into a power outlet near your router, switch, or NVR.
2. Connect the receiver to the network device (router, switch or recorder) using a UTP cable.
3. Make sure the Powerline transmitter(s) are connected to a different socket and paired according to the manual.
4. Check the status LEDs on the transmitter and receiver for an active connection.
5. Your IP cameras and other devices can now communicate with the receiver via the power grid.

Technical specifications

– Model: SCS-P1200P1 (Powerline Adapter Receiver)
– Maximum throughput speed: 1200 Mbps (theoretical)
– Power supply: 100–240V~ 50/60 Hz
– Dimensions: approximately 110 x 65 x 40 mm
– Protocol: HomePlug AV2
– Network standards: IEEE 802.3, IEEE 802.3u (10/100 Ethernet)

Package contents

– 1x Powerline Adapter Receiver SCS-P1200P1
– 1x Ethernet cable (UTP)
– 1x Installation manual

Buy Powerline Adapter Receiver SCS-P1200P1 at Sitcon

Sitcon has specialized in security and surveillance products for both residential and professional use since 2007. All products are tested in-house for functionality, reliability, and ease of use, so you can be sure the Powerline Adapter Receiver SCS-P1200P1 will integrate seamlessly with your camera system or network solution. You can visit our stores in Utrecht (Netherlands) and Maaseik (Belgium) for personalized advice and demonstrations.

When you order through our webshop, you benefit from clear product information, after-sales support, and the added security of Thuiswinkel Waarborg (Home Shopping Guarantee). This combines the convenience of online ordering with the assurance of a specialist who knows their products inside and out.

Frequently Asked Questions

Can I use the Powerline Adapter Receiver SCS-P1200P1 separately without a transmitter?

No, the receiver cannot function independently. The SCS-P1200P1 always requires a paired Powerline transmitter, such as the SCS-P1200P2 or a transmitter from a complete Powerline set. Without a transmitter, there is no data transfer via the powerline, and the receiver will not establish a network connection.

Where do I place the receiver in my installation?

Ideally, you should plug the receiver into a power outlet near your router, network switch, or NVR. Then, use the included UTP cable to connect the receiver to this network device. This way, all traffic from the Powerline transmitters converges via the electrical wiring at this central point in your network.

Does this receiver only work with the SCS-P1200P2 transmitter?

The SCS-P1200P1 is designed to work with the corresponding SCS-P1200P2 Powerline transmitter and sets based on the same HomePlug AV2 protocol and pairing mechanism. To ensure stable operation, we recommend using the receiver in conjunction with the corresponding transmitter and not mixing it with other Powerline systems of unknown origin.

Is a speed of 1200 Mbps always achievable?

The stated 1200 Mbps is a theoretical maximum speed under ideal conditions. In practice, the actual speed depends on factors such as the quality of the electrical installation, the length of the power cables, the number of circuits, and sources of interference in the network. However, for most IP camera and network applications, the practical speed is more than sufficient.

Can I connect devices other than IP cameras to this receiver?

Yes, you can connect any device with a wired Ethernet connection to the receiver, such as an NVR, computer, switch, or other network device. As long as the device can communicate with the receiver via UTP and the total data traffic remains within reasonable limits, the receiver is used in a similar way to a standard network cable.

Does the Powerline Adapter Receiver affect the power grid or other devices?

The Powerline Adapter Receiver uses the electrical network as a transport medium for data signals, but has no noticeable impact on your normal power consumption. Other devices connected to the same circuit continue to function normally. In some situations, heavy loads or interfering power supplies may affect the data speed, but this has no negative impact on the safety or operation of the power supply itself.